Every time I looked at it, I thought of a dress. And since that means it was pretty girly and the hubs wouldn’t mind NOT having it on the table, and despite him teasing me for making a table runner and then using it for a dress, I gave it a go. :)
On Wednesday, I will show you the honest truth about the process, but for now? Let’s just enjoy Lil’ Miss B in her new Sunshine Dress, all the quirks worked out…
I’m going to show you how to make one, too!
This dress tutorial is for a size 18 month – 2T. I will include a few tips on adjusting the size at the very end. There are no buttons or zippers on the back. The button you see at the neckline holds that side together. I can get this dress on and off my little B without any problems.
The dress takes about 2-3 hours to make. So although it is easy, it does take some time.
What You Need:
-Four pieces of fabric cut using Pattern A (downloadable pattern piece HERE). Cut two lining, two outer fabric. (So one outer, one lining for piece 1, and one outer, one lining for piece 2)
-Four pieces of fabric cut using pattern B (downloadable pattern piece HERE). Cut two outer and 2 lining, for around neck
-Two 18.25” x 12” pieces of patterned fabric for the bottom portion. OR, one rectangle piece measuring (I used the two 18.25” pieces because I wanted the patterns to be symmetrical)
-One 36” x 12” piece fabric for lining
-Two 12” x 3” pieces fabric for middle triangle (can be plain like I did, or coordinating fabric)
-Two 60” x 2.5” strips knit for ruffles
-Four 2” x 18” pieces of fabric for ties (two pattern, two lining)
*Please note that all seam allowances are 1/4” (in case I forgot to put it somewhere)*
Step 1: Start by sewing the two 18.25” pieces together just along one side. Then sew 1/4” seam around 3 sides (leaving the top long side open) with the outer and lining fabric right sides together.
Clip the bottom two corners, turn right side out, and topstitch around the three sides you sewed together.
Step 2: Onto the best part, right? Ruffles! Take the two 60” strips of knit and sew a basting stitch. Pull from either side to ruffle.
Mark with a non-permanent pen/pencil/chalk on your bottom portion where you want to sew the ruffles on. Sew them on following your basting stitch.
Step 3: Take the two 12” x 3” pieces, and sew around 3 sides, leaving one of the short sides open.
Slip corners and turn. Place in the middle of the lining fabric on the bottom portion you’ve been working with.
Fold the piece in towards the middle, making the top hit near the middle of the small rectangle and the bottom lining up with the corner, to create a triangle shape. See next two pictures to better understand:).
Pin and sew using a topstitch. I didn’t want to sew my ruffle down so I just skipped it and then started underneath it.
Zig-zag stitch or serge along the unfinished edge of the bottom portion. Set aside.
Step 4: Take one of the outer and one inner of Pattern B. Sew together along arm holes, strap part, and neck. Leave the sides and bottom open. Clip corners and clip all around curved areas.
Turn and zig-zag or serge the sides and bottom. Topstitch around the armholes. Repeat with the other two pieces.
Now take the two upper portions of the dress and zig-zag stitch together the left arm hole (if you were wearing it).
You can’t see it very well, but the left arm hole is sewed, and the right is left open.
Step 5: Let’s take the four 2” x 18” strips of fabric and make the ties. Take a pattern and a lining piece, right sides together, and sew, leaving one short side open. Clip corners, turn, and topstitch around it. No need to tuck in the unfinished side. Just sew a seam there too. Repeat with other strips of fabric to make the other tie.
Place one of the ties in between the right sides of the two upper portions of dress. (I did fix Pattern B to allow for more space for the strap to fit).
Sew 1/4” seam, then turn and topstitch the tie towards the back like pictured. Repeat with other strap.
Step 6: Take your bottom portion and sew two basting stitches around the entire top of it and pull to gather.
Keep gathering and adjusting so that it fits the top portion. Pin and sew along the bottom basting stitch. See second picture below? You are putting the right sides together of the bottom and upper parts of the dress.
If you did not sew along the bottom basting stitch like me then unpick it if you want:).
Step 7: Take the two fabric pieces cut from Pattern A, Piece 1, and sew together, leaving one of the short sides open. Clip corners and curves. Turn. Repeat the same steps with Piece 2.
Place around the neckline to determine this next part. You aren’t sewing it on the dress yet, you are just making sure that the pieces are matching up to know where to sew. Tuck one of the unfinished ends in, and place the other raw edge inside that. Sew together.
So you’ll have this:
Step 8: Now pin it around the neckline.
Topstitch, starting at the top of the shorter curved piece (on the front of the dress). Go all around to the back and up the flap, and just keep topstitching around the whole thing, back around the bottom of this neck piece.
So you’ll have this now.
Mark where you want the button and buttonhole and sew those. You could maybe do a fake button with velcro, snaps, or a hook & eye. I wanted a button just for strength.
Attach a flower in the middle and you are done!
As always, let me know if you have trouble with anything, or if something seems unclear. I’d be happy to answer any questions you might have.
I'm linking to these parties:).